| Flow Splitters for Chromatography |
|
|---|---|
Model 62 Stainless Steel Adjustable
Flow Splitter For Pre and Post Column Applications |
|
 |
•
Bracket Mounted • Adjustable Metering • Precise Direct Control • Fluid Resistor Technology • Split ratios from 1:1 to 20,000:1 • Low Dead Volume • Rugged Steel Design • 5,000 PSI Valve Limit |
Adjustable Flow Splitters make it easy to create split ratios from 1:1 up to as
high as 20,000:1. Because the Adjustable Flow Splitter incorporates a metering
valve, split ratios can be changed frequently with flow changes that are stable
and reproducible as noted in figure 1.0. Our Model 62 splitter valve ratios are
not affected by changes in solvent viscosities or pressure, which makes this
product acceptable for gradient and isocratic applications. Other applications
include SCF/MS, where large viscosity changes may be encountered during gradient
runs. Applications include isocratic and gradient methods where a reproducible
change in the split ratio is acceptable. Split ratios are created by two fluid resistors that form a parallel flow path. The low flow rate stream passes through a fixed resistor cartridge, while the high flow rate stream passes through an adjustable fluid resistor (metering valve). The ratio of these two resistors creates the split flow ratio. The resulting ratios are stable and repeatable. Because of the rugged design, the split ratio repeatability is ± 1% of setting, and unlike alternative splitter valves or tees, will not be affected by actions that effect input flow such as turning the pump off and on, or pressure spikes. Pre-Column splitting is used for micro, capillary and nano HPLC applications. Keep in mind that even though the split ratio created by the splitter valve will remain constant; when an HPLC column is installed there will be added resistance on the flow rate channel from the HPLC column. This added resistance must be factored in to make sure the fluid resistor selected for the flow splitter provides the correct split ratio. When ordering a pre-column flow splitter please provide Analytical Sales with the column flow rate and back pressure. If the inlet flow rate or column pressure specifications are not provided, Analytical Sales will configure pre-column flow splitters assuming a 0.5mL/min inlet flow rate and a pressure drop across the column of 1500 PSI. |
|
Model 62 Post
Column Adjustable Flow Splitters Analytical Range: 0.1 - 5mL/min Incoming Flow |
|
|---|---|
Catalog No. |
Description |
62-414 |
Adjustable Splitter, Stnls Steel w/ -06 Resistor Cartridge Ratio 1:1 - 20:1 |
62-413 |
Adjustable Splitter,
Stnls Steel w/ -04 Resistor Cartridge Ratio 4:1 - 100:1 |
62-412 |
Adjustable Splitter,
Stnls Steel w/ -03 Resistor Cartridge Ratio 15:1 - 250:1 |
62-411 |
Adjustable Splitter,
Stnls Steel w/ -01 Resistor Cartridge Ratio 50:1 - 1000:1 |
Replacement Resistor Cartridges for Model 62 Adjustable Flow Splitters |
|
61-115 |
Analytical -06
Resistor Cartridge Ratio 1:1 - 20:1 |
61-114 |
Analytical -04
Resistor Cartridge Ratio 4:1 - 100:1 |
61-113 |
Analytical -03
Resistor Cartridge Ratio 15:1 - 250:1 |
61-112 |
Analytical -01
Resistor Cartridge Ratio 50:1 - 1000:1 |
Adjustable Semi-Prep
Flow Splitters
Analytical Range: 5.0 - 40mL/min Incoming Flow
Catalog No. Description
62-315
Adjustable Semi-Prep Splitter, Stnls Steel 1:1 - 20:1
62-313 Adjustable Semi-Prep
Splitter, Stnls Steel 15:1 - 300:1
62-312 Adjustable Semi-Prep
Splitter, Stnls Steel 100:1 - 2000:1
62-315 Adjustable Semi-Prep
Splitter, Stnls Steel 1000:1 - 20,000:1
Replacement Inlet
Filters for Adjustable Flow Splitters
Replacing the inlet filter prevents the splitter
from clogging
66-063 Replacement
Analytical Inlet Filter, 2µm x 0.063 dia., 5/pkg
Adjustable Pre-Column Flow Splitters
Pre-Column splitting is used for micro,
capillary and nano HPLC applications. The split ratio created by the
splitter valve will remain constant, however, when an HPLC column is
installed there will be added resistance on the flow rate channel. This
added resistance must be considered to ensure the fluid resistor selected
for the flow splitter provides the correct split ratio.
When ordering a
pre-column flow splitter, please provide the column flow rate and back
pressure specifications. If these specifications are not provided, the
pre-column flow splitter will be configured assuming a 0.5mL/min inlet flow
rate and a pressure drop across the column of 1500psi.
Adjustable Pre-Column Splitter
Analytical Range: 0.1 - 1mL/min Incoming Flow
These splitters will produce under 3500 PSI
back pressure with water at 0.5mL/min
Catalog No. Description
60-101
Adjustable Pre-Column Splitter Split Ratio Range 50:1 -
1000:1
60-103 Adjustable Pre-Column
Splitter Split Ratio Range 15:1 - 250:1
60-104 Adjustable Pre-Column
Splitter Split Ratio Range 5:1 - 100:1
60-106 Adjustable Pre-Column
Splitter Split Ratio Range 1:1 - 20:1
Replacement Resistor Cartridges for Adjustable
Pre-Column Splitters
60-001 Adjustable Pre-column
Resistor Cartridge Split Ratio Range 50:1 - 1000:1
60-003 Adjustable Pre-column
Resistor Cartridge Split Ratio Range 15:1 - 250:1
60-004 Adjustable Pre-column
Resistor Cartridge Split Ratio Range 5:1 - 100:1
60-006 Adjustable Pre-column
Resistor Cartridge Split Ratio Range 1:1 - 20:1
Model 63 and 53 Fixed Binary and
Multiport Flow Splitters
• Fixed metering for precise control
• Fluid Resistor Technology
• Split ratios from 1:1 to 2,000:1
• Low dead volume
• Rugged stainless steel design
The Advantage Fixed Flow Splitters are shipped with resistors installed that deliver the nominal stated split ratio. The split ratios have a tolerance range of ±10%. The exact split ratio is measured and is stated on the certificate shipped with the splitter. The input flow rate can be adjusted to compensate for the tolerance in split ratios. For instance, a 10% increase in input flow rate will result in a 10% increase in flow at both the capillary and waste stream channels. Flow rate and viscosity changes will change the backpressure generated by the splitter, but will not affect the actual split ratio.
These fixed Flow Splitters can be used for LC/MS, Flow Fractionation, Column Flow Splitting and Capillary Chromatography.
Model 63 Post Column
Binary Fixed Flow Splitters
Analytical Range: 0.1-5mL/min Incoming Flow
Catalog No. Description
63-423
Binary Fixed Splitter, Ratio 1:1
63-422 Binary Fixed
Splitter, Ratio 3:1
63-424 Binary Fixed
Splitter, Ratio 4:1
63-421 Binary Fixed
Splitter, Ratio 5:1
63-420 Binary Fixed
Splitter, Ratio 10:1
63-419 Binary Fixed
Splitter, Ratio 20:1
63-418 Binary Fixed
Splitter, Ratio 50:1
63-417 Binary Fixed
Splitter, Ratio 100:1
63-416 Binary Fixed
Splitter, Ratio 200:1
63-415 Binary Fixed
Splitter, Ratio 500:1
63-414 Binary Fixed
Splitter, Ratio 1,000:1
63-413 Binary Fixed
Splitter, Ratio 2,000:1
63-666 Binary Fixed
Splitter, Custom Ratio
Accessories and Replacement Components
63-111
Mounting Bracket for Fixed Splitter
Replacement Inlet Filter, Binary Fixed Splitters,
Model 63
Replacing the inlet filter prevents clogging of the splitter
77-125 Binary Analytical
Inlet Filter, 2µm x 0.063 dia., 5/pkg
Replacement Resistors for Post Column
Binary Fixed Splitters, Model 63
63-443 Replacement Binary
Resistor, Ratio 1:1
63-442 Replacement Binary
Resistor, Ratio 3:1
63-441 Replacement Binary
Resistor, Ratio 5:1
63-440 Replacement Binary
Resistor, Ratio 10:1
63-439 Replacement Binary
Resistor, Ratio 20:1
63-438 Replacement Binary
Resistor, Ratio 50:1
63-437 Replacement Binary
Resistor, Ratio 100:1
63-436 Replacement Binary
Resistor, Ratio 200:1
Model 63 SEMI-PREP Column Binary Fixed Flow
Splitters
Analytical Range: 5.0-40mL/min Incoming Flow
63-405 Binary Fixed
Splitter, Ratio 500:1
63-410 Binary Fixed
Splitter, Ratio 1,000:1
63-402 Binary Fixed
Splitter, Ratio 2,000:1
Replacement Resistors for SEMI-PREP Column
Binary Fixed Splitters, Model 63
63-435 Replacement Binary
Resistor, Ratio 500:1
63-434 Replacement Binary
Resistor, Ratio 1,000:1
63-433 Replacement Binary
Resistor, Ratio 2,000:1
Model 53 MultiPort Fixed Flow
Splitter Manifold
Analytical Range: 0.1 - 5mL/min Incoming Flow
Multiport Splitters come mounted
on a Mounting Bracket
53-112 3 Port Fixed
Splitter, Post-Column, Custom Ratio
53-114 4 Port Fixed
Splitter, Post-Column, Custom Ratio
Contact us today for more information:
Analytical Sales and Services
230 West Parkway • Unit One
Pompton Plains, NJ 07444
Tel:
973.616.0700
Fax:
973.616.0133
E-Mail: info@analytical-sales.com